Sonnax 36948-13K 4R100 Transmission Valve Kit, Accumulator Regulator (1-2 & 2-3)

Description: 4R100, E4OD 1-2 & 2-3 Accumulator Control Valve KitSonnax Part No. 36948-13KFits either of 2 locations.Requires: Sonnax Part # 36948-12 (Recommended)Under high-pressure shifts, the valve is allowed to stroke too far, causing it to hang up on these ridges and block oil flow to the associated clutch. This results in soft shifts, loss of gear and burnt clutches. Sonnax 1-2 and 2-3 accumulator control valve kit 36948-13K resolves these issues and provides a firmer-than-OE shift quality.The step machined into valve spool acts as an orifice to allow full oil flow to clutches when appropriate, preventing premature clutch failureReinforcement retaining clip attaches to OE clip to prevent over-strokingSpring shims allow for selective increase of apply pressure to manipulate shift qualityAnnular groove helps center valve in bore to prevent future side-load wearDrop-in Zip Valve™ parts install quickly and easilyContentsValveRetaining ClipSpring Shims (4)NoteSonnax bore sizing tool 36948-12 (available separately) properly resizes the bore to prevent hang-up or sticking of the new valve. See instructions for details. Tool is recommended but not required. A NAME YOU CAN TRUSTAs an industry veteran in the transmission parts supply business, you can buy with confidence. Our goal is to provide high quality parts, an experienced sales force, and the highest levels of product availability possible.Important InformationShippingReturnsCore PolicyImportant InformationShippingReturnsCore Policy As a buyer, it is your responsibility to verify that this product is compatible with your application. For any general questions, technical support, or to verify part fitment please send us a message. Our support is free, and we typically respond within minutes. Your order will be shipped within 1 business days (MON-FRI excluding holidays) of receiving payment and you should expect to receive it five to seven days via US Postal Service or UPS Ground Standard Shipping unless another shipping method is chosen. In addition to UPS Ground, we offer expedited services as well as local pick-up. Please contact us if a quote is needed and we will be happy to work with you. Please Note: All packages valued at over $500 WILL require a signature upon delivery. If your package arrives damaged, please do not open and contact us immediately. If your package is returned by the carrier due to address errors, you will be responsible for the shipping cost. International Customers: Please make sure you monitor your package. Any import duty/taxes must be paid by the buyer. If you do not pay in a timely fashion your package will be returned. You will not receive a refund for the returned items until they’re delivered. Shipping fees will not be reimbursed. 30 Day return policy for unused, uninstalled items. Any product you return must be in the same condition you received it and in the original packaging. If you’re having an issue with a used or remanufactured item and it’s been installed, we require the buyer to contact us immediately so we can provide trouble shooting information. Worst case scenario if that fails, exchange only. Certain item such as used items, tools, and one time use items are not eligible for return. As a buyer, it is your responsibility to verify that this product is compatible with your application. If you ordered the wrong item for your application YOU are responsible for the return shipping. 20% Restocking Fee May Apply If you are purchasing an item in which a core charge is required, please be sure your contact information is current. If core charge is not paid within 1 week of purchase, your order will be cancelled. Upon receiving your new part, there will be a prepaid shipping label included so you can return your core (old part) to us free of charge. Please make sure to use the label we send you. You have 14 days to ship your core back to us from the time your new part was delivered. If you do not ship the core within 14 days, you WILL LOSE YOUR REFUNDABLE CORE CHARGE. Exceptions are possible, BUT YOU MUST contact us to make us aware of the situation. ATTENTION INTERNATIONAL BUYERS: Due to the inflation of shipping costs, we are unable to pay for the return shipping on the core. If you want the core charge refunded, you will have to pay for shipping. We apologize for any inconvenience this may cause. Once your core is delivered, please allow 3-5 business days for your refund to be processed. See our other items4R100, E4OD 1-2 & 2-3 Accumulator Control Valve Kit Sonnax Part No. 36948-13K Fits either of 2 locations. Requires: Sonnax Part # 36948-12 (Recommended) Under high-pressure shifts, the valve is allowed to stroke too far, causing it to hang up on these ridges and block oil flow to the associated clutch. This results in soft shifts, loss of gear and burnt clutches. Sonnax 1-2 and 2-3 accumulator control valve kit 36948-13K resolves these issues and provides a firmer-than-OE shift quality. ---The step machined into valve spool acts as an orifice to allow full oil flow to clutches when appropriate, preventing premature clutch failure ---Reinforcement retaining clip attaches to OE clip to prevent over-stroking ---Spring shims allow for selective increase of apply pressure to manipulate shift quality ---Annular groove helps center valve in bore to prevent future side-load wear ---Drop-in Zip Valve™ parts install quickly and easily Contents ---Valve ---Retaining Clip ---Spring Shims (4) Note ---Sonnax bore sizing tool 36948-12 (available separately) properly resizes the bore to prevent hang-up or sticking of the new valve. See instructions for details. Tool is recommended but not required. 4R100, E4OD 1-2 & 2-3 Accumulator Control Valve KitSonnax Part No. 36948-13KFits either of 2 locations.Requires: Sonnax Part # 36948-12 (Recommended)Under high-pressure shifts, the valve is allowed to stroke too far, causing it to hang up on these ridges and block oil flow to the associated clutch. This results in soft shifts, loss of gear and burnt clutches. Sonnax 1-2 and 2-3 accumulator control valve kit 36948-13K resolves these issues and provides a firmer-than-OE shift quality.The step machined into valve spool acts as an orifice to allow full oil flow to clutches when appropriate, preventing premature clutch failureReinforcement retaining clip attaches to OE clip to prevent over-strokingSpring shims allow for selective increase of apply pressure to manipulate shift qualityAnnular groove helps center valve in bore to prevent future side-load wearDrop-in Zip Valve™ parts install quickly and easilyContentsValveRetaining ClipSpring Shims (4)NoteSonnax bore sizing tool 36948-12 (available separately) properly resizes the bore to prevent hang-up or sticking of the new valve. See instructions for details. Tool is recommended but not required. A NAME YOU CAN TRUSTAs an industry veteran in the transmission parts supply business, you can buy with confidence. Our goal is to provide high quality parts, an experienced sales force, and the highest levels of product availability possible.Important Information As a buyer, it is your responsibility to verify that this product is compatible with your application. For any general questions, technical support, or to verify part fitment please send us a message. Our support is free, and we typically respond within minutes. Shipping Your order will be shipped within 1 business days (MON-FRI excluding holidays) of receiving payment and you should expect to receive it five to seven days via US Postal Service or UPS Ground Standard Shipping unless another shipping method is chosen. In addition to UPS Ground, we offer expedited services as well as local pick-up. Please contact us if a quote is needed and we will be happy to work with you. Please Note: All packages valued at over $500 WILL require a signature upon delivery. If your package arrives damaged, please do not open and contact us immediately. If your package is returned by the carrier due to address errors, you will be responsible for the shipping cost. International Customers: Please make sure you monitor your package. Any import duty/taxes must be paid by the buyer. If you do not pay in a timely fashion your package will be returned. You will not receive a refund for the returned items until they’re delivered. Shipping fees will not be reimbursed. Returns 30 Day return policy for unused, uninstalled items. Any product you return must be in the same condition you received it and in the original packaging. If you’re having an issue with a used or remanufactured item and it’s been installed, we require the buyer to contact us immediately so we can provide trouble shooting information. Worst case scenario if that fails, exchange only. Certain item such as used items, tools, and one time use items are not eligible for return. As a buyer, it is your responsibility to verify that this product is compatible with your application. If you ordered the wrong item for your application YOU are responsible for the return shipping. 20% Restocking Fee May Apply Core Policy If you are purchasing an item in which a core charge is required, please be sure your contact information is current. If core charge is not paid within 1 week of purchase, your order will be cancelled. Upon receiving your new part, there will be a prepaid shipping label included so you can return your core (old part) to us free of charge. Please make sure to use the label we send you. You have 14 days to ship your core back to us from the time your new part was delivered. If you do not ship the core within 14 days, you WILL LOSE YOUR REFUNDABLE CORE CHARGE. Exceptions are possible, BUT YOU MUST contact us to make us aware of the situation. ATTENTION INTERNATIONAL BUYERS: Due to the inflation of shipping costs, we are unable to pay for the return shipping on the core. If you want the core charge refunded, you will have to pay for shipping. We apologize for any inconvenience this may cause. Once your core is delivered, please allow 3-5 business days for your refund to be processed. See our other items 4R100, E4OD 1-2 & 2-3 Accumulator Control Valve KitSonnax Part No. 36948-13KFits either of 2 locations.Requires: Sonnax Part # 36948-12 (Recommended)Under high-pressure shifts, the valve is allowed to stroke too far, causing it to hang up on these ridges and block oil flow to the associated clutch. This results in soft shifts, loss of gear and burnt clutches. Sonnax 1-2 and 2-3 accumulator control valve kit 36948-13K resolves these issues and provides a firmer-than-OE shift quality.The step machined into valve spool acts as an orifice to allow full oil flow to clutches when appropriate, preventing premature clutch failureReinforcement retaining clip attaches to OE clip to prevent over-strokingSpring shims allow for selective increase of apply pressure to manipulate shift qualityAnnular groove helps center valve in bore to prevent future side-load wearDrop-in Zip Valve™ parts install quickly and easilyContentsValveRetaining ClipSpring Shims (4)NoteSonnax bore sizing tool 36948-12 (available separately) properly resizes the bore to prevent hang-up or sticking of the new valve. See instructions for details. Tool is recommended but not required.

Price: 14.3 USD

Location: Shepherdsville, Kentucky

End Time: 2024-07-28T15:01:58.000Z

Shipping Cost: N/A USD